what motor parts will fit for a 95 es 2.5l v6 veng. ive read something about some dsm parts but are there any more? thanks for your help. btw im new to the veng scean
What kind of parts are you looking for? There are simple items like intake and exhaust, and more advanced ones like the 3.0 swap and boosting. Please be a little more specific with the type of application. Then the gurus will be able to help ya out more.
good question, however more accurately its what wont fit, headers is one of the biggest gripes and well so is a turbo since no one makes one oh and superchargers as well.
simple stuff not looking for something i have to rob a bank to get .... so simple stuff like intake, fuel delivery, and such. thank you for welcoming me.
intakes are easy, i was told that the same intakes will fit the 4 and 6 cylinder so its hard to find one, you can find a lot in the search tab thats at the top of the screen. I asked these same questions a few months back and also Welcome to the board!!!!! there is a bosal cat back exhaust for the V6 as well. Nykon has a sound clip of his bosal hooked up to his eclipse in the 4 cyl tech forum i think its under exhaust sounds.
Headers (hard to find), intake (good ones on ebay), Downpipe (contact sroufe on the board), Underdrive Pulley (Group buy going on right now on the board).
There's other's like MSD ignition and grounding kits that just help overall. Take a look around the board, you should be able to find more... and Welcome.
Logged
Scott --> http://www.cardomain.com/ride/2542075 <-- 97 Chrysler Sebring Lxi 2.5L V6 - CAI, Accel 8mm wires, CCG UDP, high flow Down pipe/Magnaflow Cat, Neuspeed STB, Megan Racing rear brace.
welcome to the board, get familiar with the general discussions so u can be more comfortable with ur questions. I see that there are already some suggestions, so u should have a good start. as for me, all my parts are custom, not finished for the most part save for the manifold and throttle body bore. stick around and u will find a lot of useful info.
asog.net/aseclub.net/ebay.com(but be careful, post items for evaluation before buying...no tornados or chips) not many engine parts, but for exhaust you can contact sroufe7 (send him a pm) he has downpipes. my suggestion is to get a cold air intake and then do a full exhaust. if u want..u can remove the pre-cat (catalytic converter) in the rear manifold. this frees up the exhaust system a bit. use this in combination with the downpipe and a hi- flow cat (also from sroufe7) and you should have a decent exhaust system. when those are done, there should be plenty small stuff here and there. you might be late for the group buy for the under drive pulley which is never really around, but ten ppl should be enough to get it done.
welcome to the community jeremiah. i only have a few "mods" to my '95 veng… one of which happens to be a CAI. i have an AEM CAI with the bypass valve. no complaints with it. it's relatively inexpensive & easy to install (with the exception of getting that huge cone filter in front of the tire—i didn't wanna take the fender well out, lol. hang around long enuff and u'll find that i'm pretty lazy ). other than that, just take the advice of the ppl here… they know there stuff!
cling clank clank… that's my 2¢
oh yeah, btw, JusBringIt. what's going on with the fund?? the last few times i've seen your posts it's decreased by 2¢. have you been dipping?? ah well, you can had that to the tally
Logged
i'm a peripheral visionary. i can see into the future, but way off to the side.
Author
Logged
). other than that, just take the advice of the ppl here… they know there stuff!
